How To Measure A Western Saddle Gullet

How To Measure A Western Saddle Gullet. Peek between the skirts in the front and find the connection between the top of the saddle bars where they connect to the pommel. The gullet of the saddle is the gap between the two bars of the saddle tree.

Draft Horse Australian Saddle by Sydney Saddleworks from frontierequestrian.com

We need your help to work out if a standard or superwide smartflx gullet will fit your horse best. Peek between the skirts in the front and find the connection between the top of the saddle bars where they connect to the pommel. When the saddle is on your horse, fit three fingers between the front part of the saddle edge or skirt/wings and the horse’s withers.

Source: frontierequestrian.com

Most gullet measurements are taken on a raw saddle tree and not on a finished saddle. It is measured at the front of the saddle.

Source: equineink.com

If three or more fingers fit, the gullet is too narrow. Peek between the skirts in the front and find the connection between the top of the saddle bars where they connect to the pommel.

Source: www.synergistsaddles.com

Most gullet measurements are taken on a raw saddle tree and not on a finished saddle. If three or more fingers fit, the gullet is too narrow.

Source: dreamstime.com

It is measured at the front of the saddle. You will need to look at the saddle’s position from the front of the horse.

Source: www.cuteness.com

Keep in mind, this measurement can be used as a rough indicator for bar angle, but it is never a guarantee. Seat size is measured from the top of the cantle (at the stitching), where the leather and seat material are attached, to the pommel or under the horn, right above the hole of the seat.

Source: outwestsaddlery.com

Place your tape ever so slightly below that joint on the inside of the gullet on the fleece and measure across to the other side in the same place. How to measure a western saddle for gaited horses if you have a gaited horse, such as a tennessee walker or fox trotter, you might need a tree designed especially for these horses.

Source: www.horsesaddleshop.com

Place your hand into the space between the saddle and your horse’s wither, using your fingers to measure the vertical space. September 24, 2020 october 22nd, 2020 no comments.

Source: americansaddlery.com

The span of the gullet should cover the withers of your horse, leaving a gap of around 2 inches between the top of the withers and the bottom of the saddle. You measure your western saddle’s gullet by stretching a tape measure from concho to concho across the front of the saddle directly below the pommel.

How To Properly Measure A Saddle Gullet On A Completed Saddle:

Keep in mind, this measurement can be used as a rough indicator for bar angle, but it is never a guarantee. Place your hand into the space between the saddle and your horse’s wither, using your fingers to measure the vertical space. Seat size is measured from the top of the cantle (at the stitching), where the leather and seat material are attached, to the pommel or under the horn, right above the hole of the seat.

Unfortunately, No Standards For Gullet Measurements Exist Within The Saddle Industry.

Please follow these instructions to take the right measurements: The gullet of the saddle is the gap between the two bars of the saddle tree. Slide three fingers down the length of the gullet when you flip the saddle over to reveal the underside as most saddles should have a gullet channel that’s at least three fingers wide.

The Swell Gullet Width Is Measured From The Point Where The Top Of The Bar Meets The Bottom Of The Swell And Across To The Same Point On The Other Side ( See Example A, A Swell Width Of 6 1/2″ ).

The trees for saddles made for gaited horses have a higher gullet. You measure your western saddle’s gullet by stretching a tape measure from concho to concho across the front of the saddle directly below the pommel. If fewer than two fingers fit, the gullet is too wide.

Place Your Tape Ever So Slightly Below That Joint On The Inside Of The Gullet On The Fleece And Measure Across To The Other Side In The Same Place.

You will need to look at the saddle’s position from the front of the horse. You measure your western saddle’s gullet by stretching a tape measure from concho to concho across the front of the saddle directly below the pommel. Most gullet measurements are taken on a raw saddle tree and not on a finished saddle.

The Gap Should Fit No More Than Two Fingers To Two And A Half Fingers.

It is measured at the front of the saddle. To measure a western saddle you should measure the distance between the highest point of the cantle to the top of the gullet. The span of the gullet should cover the withers of your horse, leaving a gap of around 2 inches between the top of the withers and the bottom of the saddle.